Search Results

Physical, chemical, and biological characterization data for the particulate emissions from a Caterpillar 3208 diesel engine with and without Corning porous ceramic particulate traps are presented. Measurements made at EPA modes 3,4,5,9,lO and 11 include total hydrocarbon, oxides of nitrogen and total particulate matter emissions including the solid fraction (SOL), soluble organic fraction (SOF) and sulfate fraction (SO4), Chemical character was defined by fractionation of the SOF while biological character was defined by analysis of Ames Salmonella/ microsome bioassay data. The trap produced a wide range of total particulate reduction efficiencies (0-97%) depending on the character of the particulate. The chemical character of the SOF was significantly changed through the trap as was the biological character. The mutagenic specific activity of the SOF was generally increased through the trap but this was offset by a decrease in SOF mass emissions.

A 1-D 2-layer model developed previously at MTU was used in this research to predict the pressure drop, filtration characteristics and various properties of the particulate filter and the particulate deposit layer. The model was calibrated and validated for this CPF with data obtained from steady state experiments conducted using a 1995 Cummins M11-330E heavy-duty diesel engine with manual EGR and using ULSF. The CPF used is a NGK filter having a cordierite substrate with NEX catalyst type formulation (54% porosity, 15.0 μm mean pore diameter and 50 gms/ft3 Pt). The filter was catalyzed using a wash coat process. The model was used to predict the pressure drop, particulate mass retained inside the CPF, particulate mass filtration efficiency and concentration downstream of the CPF with agreement between the experimental and simulated data.

A study was conducted to assess the effects of controlling filter face temperatures and two differently sized collection systems on diesel total particulate matter (TPM) and vapor phase hydrocarbon levels from a diesel engine. The results were used to revise sampling protocols so that variability associated with quantitation of polynuclear aromatic hydrocarbons (PAH) is minimized. Particulate soluble organic fraction (SOF) levels (%) were compared 1) for tests where the dilute exhaust filter face temperature was held constant by varying dilution ratio (DR) to account for day to day variations in inlet air temperature to the tunnel and 2) for tests in earlier studies where the DR was held constant and the filter face temperature then varied because of varying tunnel inlet air temperature. Between date variations in %SOF were reduced by about 60% due to holding filter face temperatures constant, compared to holding DR constant.

One of the more objectionable aspects of the use of the diesel engine is its emission of particulate matter. Methods for collecting particulate matter samples in the undiluted exhaust gases with an Andersen Impactor for gravimetric and electron microscopy analysis are developed. A direct injection Vee-eight naturally aspirated diesel engine was used in the study. This paper presents the results of an in-depth study of the physical characteristics of diesel particles. The size distribution of the particulate matter was obtained using an Andersen Inertial Impactor for the engine conditions applicable to the SAE 13-mode cycle. The particulate matter was analyzed using both scanning and transmission electron microscopes and was found to be comprised of individual spherical particles ranging from 100 ņ to 800 Å with a mean size of approximately 260 Å. The particulate matter was analyzed for carbon, hydrogen and nitrogen.

A study was undertaken to investigate the affect of exhaust gas recirculation (EGR) on engine wear and lubricating oil degradation in a heavy duty diesel engine using a newly developed methodology that uses analytical ferrography in conjunction with short term tests. Laboratory engine testing was carried out on a Cummins NTC-300 Big Cam II diesel engine at rated speed (1800 RPM) and 75% rated load with EGR rates of 0, 5, and 15% using a SAE 15W40 CD/SF/EO-K oil. Dynamometer engine testing involved collecting oil samples from the engine sump at specified time intervals through each engine test. These oil samples were analyzed using a number of different oil analysis techniques that provide information on the metal wear debris and also on the lubricating oil properties. The results from these oil analysis techniques are the basis of determining the effect of EGR on engine wear and lubricating oil degradation, rather than an actual engine tear down between engine tests.

Heavy-duty diesel engine particulate matter (PM) emissions must be reduced from 0.1 to 0.01 grams per brake horsepower-hour by 2007 due to EPA regulations [1]. A catalyzed particulate filter (CPF) is used to capture PM in the exhaust stream, but as PM accumulates in the CPF, exhaust flow is restricted resulting in reduced horsepower and increased fuel consumption. PM must therefore be burned off, referred to as CPF regeneration. Unfortunately, nominal exhaust temperatures are not always high enough to cause stable self-regeneration when needed. One promising method for active CPF regeneration is to inject fuel into the exhaust stream upstream of an oxidation catalytic converter (OCC). The chemical energy released during the oxidation of the fuel in the OCC raises the exhaust temperature and allows regeneration.